Bridge Bearings & Expansion Joints
Structural bearings and expansion joints for highway, railway and municipal bridges. Pot and spherical bearings provide vertical support, transfer or release horizontal load, and accommodate rotation and displacement. Expansion joints accommodate three-dimensional deck movement, transfer braking forces and seal the deck against water and debris, in modular, comb plate and elastomeric seamless forms.
Pot bearings are supplied to typical design loads of 800 to 60,000 kN and spherical bearings to 800 to 160,000 kN, configured as fixed, guided sliding or free sliding depending on the restraint and design, with PTFE sliding against stainless steel and elastomer pads suitable down to -40 °C. Laminated elastomeric bearings are built from natural rubber or chloroprene rubber with vulcanised steel reinforcing plates, covering vertical loads from about 189 kN to 7,353 kN at service temperatures of -40 °C to +50 °C. High-damping and lead-core seismic units reach 360% and 400% shear deformation.
Expansion joints accommodate longitudinal and transverse movement, angular and plan rotation, and transfer vertical and horizontal braking forces while sealing the deck. Single-seal joints take 40 to 80 mm movement with hot-rolled edge beams and a replaceable EPDM strip seal of 60±5 IRHD, ≥14 MPa tensile strength and ≥350% elongation, serviceable from -40 °C to +60 °C. Modular joints are built in 80 mm gap increments to 160 to 640 mm total movement, with closed-cell polyurethane control springs, PTFE sliding surfaces and shop-applied epoxy zinc-rich or 80 µm galvanised protection. Large displacement installations to 2,100 mm are engineered to the project.
- EN 1337-2 / -5 / -7 — sliding elements, pot bearings and spherical bearings for structural applications.
- EN 1337-3:2005 — elastomeric bearings — types A to F with load, movement and rotation tables.
- EN 15129:2009 — anti-seismic devices, applied to high-damping and lead-core rubber bearings.
- BS 5400 — steel, concrete and composite bridges — structural bearing requirements.
- AASHTO LRFD — bridge design specification referenced for bearing and joint design.
- DIN 4141 / ETAG-032 — expansion joint project compliance references.
- EN 1337-4 / EN 1337-6 — roller bearings and rocker bearings for structural applications.
CRCC certification is held where the project requires it. Where the project cites a national annex or an owner bridge standard, the bearing or joint is designed and certified to it.
- Highway & municipal bridges — bearings and deck joints for road overpasses and expressways.
- Railway & metro bridges — bearings and joints for main line and urban rail structures.
- Long-span crossings — large-movement modular joints on cable-stayed and cross-sea bridge projects.
- Seismic isolation — high-damping and lead-core bearings for structures in seismic zones.
- Industrial & pipe bridges — bearings and movement joints for plant pipe racks and conveyor structures.
- Type test reports to EN 1337 for the supplied bearing type and load range.
- Material certificates to EN 10204 3.1 for steel components, PTFE and elastomer.
- CRCC certification, plus CE marking to ETA where required.
- Fatigue and displacement cycle test records for expansion joints.
- Shear, compression and adhesion bond testing on routine production samples.
- Annual capacity of 200,000 m of expansion joint systems and over 180 sets of large displacement joints.
- Bearing selection and joint movement calculations prepared per structure.
- Export packing, FOB / CFR / CIF to Gulf ports/global ports, with installation supervision available.
Supplied to projects across the Gulf, North and Sub-Saharan Africa, South-East Asia and Australia. Middle East supplies are subject to project-specific approval by the owner, engineer or consultant; PROTEKTA prepares and supports the submittal package for that approval.
Bridge Bearings & Expansion Joints — Buyer Questions
What load ranges are covered?
Pot bearings are typically designed for 800 to 60,000 kN and spherical bearings for 800 to 160,000 kN, in fixed, guided sliding and free sliding configurations. Sliding surfaces are PTFE against stainless steel, with elastomeric pads rated for service down to −40 °C. Supplied for projects across the GCC — Saudi Arabia, UAE, Qatar, Kuwait, Oman and Bahrain — and to Iraq, Algeria, Morocco, Nigeria, Ethiopia, Tanzania, Malaysia, Thailand, Singapore, Indonesia, Brunei and Australia, with compliance documentation prepared for consultant, contractor and authority submittal.
Which standards and certifications apply?
Bearings are supplied to EN 1337-2, -5 and -7, with BS 5400, AASHTO LRFD and DIN 4141 referenced. Expansion joints are supplied against ETAG-032, and CRCC certification is held where the project requires it. Also specified and procured as Pot Bearing, Spherical Bearing and Modular Expansion Joint; full specification ranges, material grades and datasheets are issued for tender, submittal and procurement use.
What expansion joint types are available?
Large displacement roadway and railway joints, modular expansion joints, comb plate joints and elastomeric seamless joints, with documented displacement capacities from 1120 mm to 2100 mm depending on the project. OEM, private-label and bespoke manufacture is supported for contractors, distributors and EPC packages.
Is installation support provided?
Yes. Bearing selection, joint movement calculations, installation drawings and site supervision are provided, along with type test reports and EN 10204 3.1 material certificates. Export packing, third-party inspection and consolidated shipment to Gulf ports/global ports are arranged with the order.



