Industrial Valves
Valves for water transmission, distribution, irrigation, hydropower and seawater cooling duties, manufactured from DN50 to DN6000 and supplied with fusion-bonded epoxy, polyurethane or rubber lining. The range covers gate, butterfly, ball and dual-plate check valves, with a dry-shaft design for seawater and sand-bearing service, and a patented triple-seal vacuum valve scalable to large bore for isolation duties.
Manufactured range covers double and triple eccentric butterfly valves from DN150 to DN6000, resilient seated gate valves to DN1200 at PN10-16, and metal seated gate valves from DN1000 to DN2000 at PN6-16. Bodies are supplied in ductile iron to DN3000 at PN40, and in carbon steel and special alloys to DN6000. Super duplex, Monel or Inconel are used for corrosive duty, and carbon steel bodies are offered natural rubber lined.
Selection is driven by media, pressure and maintenance access. Seawater duty uses super duplex or rubber lined carbon steel bodies with Monel K500 shafts and aluminium bronze bearings. Potable water duty uses ductile iron bodies with bronze seat rings, AISI 431 stems and A2-70 fasteners, epoxy coated to a minimum 250 µm. Actuators are specified at 380 V, IP68 and ATEX Ex d IIB T4, and large bore valves are supplied with hydraulic power units and accumulators for controlled closure.
- EN 1074-1 & -2 — valves for water supply — general requirements and isolation valves.
- EN 1171 / EN 12334 — industrial cast iron gate valves and check valves.
- EN 12266-1 & -2 — pressure testing, test procedures and acceptance criteria.
- EN 558 / ISO 5752 — face-to-face and centre-to-face dimensions, series 14 and 15.
- EN 1092-2 / ASME B16.5 — flange dimensions and pressure-temperature ratings.
- DIN 3352 / ANSI Class 150 — gate valve face-to-face and body dimensions; pressure class where scheduled.
- AWWA C207 / C504 / C509 — steel flanges, rubber seated butterfly valves and resilient seated gate valves.
- IEC 60529 — enclosure protection degrees, applied to IP68 valve actuators.
Coating to ANSI/AWWA C550 for fusion-bonded epoxy and to EN 1092-2 for flange drilling. Where the project cites BS, DIN, JIS or an owner material specification, the valve is sourced and certified to that standard and submitted against it.
- Water transmission — large bore butterfly valves and dismantling joints for transmission mains and pumping stations.
- Seawater & desalination — rubber lined and super duplex valves for intake, cooling water and pump discharge isolation.
- Irrigation — large bore butterfly valves with hydraulic or electric actuation.
- Sewage & stormwater — knife gate, swing check and sewage combination air valves.
- Oilfield water systems — metal seated gate valves for filter and settling tank isolation.
- Hydropower — turbine inlet valves and draft tube isolation at large bore.
- Production pressure testing to EN 12266, covering shell, seat and closure tests before dispatch.
- Functional testing of valves with mounted actuators under full differential pressure before shipment.
- Material certificates to EN 10204 3.1 for body, disc, shaft and fasteners.
- WRAS approved materials for potable water duty where the project requires it.
- Coating reports — dry film thickness, holiday detection and adhesion to the specified system.
- Full manufacturing workflow in-house — casting, machining, coating, assembly and testing.
- Actuator, gearbox, extension spindle and monitoring switch packages fitted and tested before shipment.
- Export packing, FOB / CFR / CIF to Gulf ports/global ports, consolidated with pipe fittings and pumps.
Supplied to projects across the Gulf, North and Sub-Saharan Africa, South-East Asia and Australia. Middle East supplies are subject to project-specific approval by the owner, engineer or consultant; PROTEKTA prepares and supports the submittal package for that approval.
Industrial Valves — Buyer Questions
What valve types and sizes can be supplied?
Gate, butterfly, ball and dual-plate check valves from DN50 to DN6000, with pressure ratings typically up to PN40. Large-bore and specialist valves, including the triple-seal vacuum valve, are engineered to the project hydraulic conditions. Supplied for projects across the GCC — Saudi Arabia, UAE, Qatar, Kuwait, Oman and Bahrain — and to Iraq, Algeria, Morocco, Nigeria, Ethiopia, Tanzania, Malaysia, Thailand, Singapore, Indonesia, Brunei and Australia, with compliance documentation prepared for consultant, contractor and authority submittal.
Which standards and certifications do the valves comply with?
Valves are supplied to EN 1074, EN 1171 and EN 12334 as applicable, pressure tested to EN 12266 or API 598, with flanges to EN 1092-2 or ASME B16.5 and face-to-face to EN 558. AWWA C509 / C515 applies to water supply service. Also specified and procured as Gate Valve, Butterfly Valve and Check Valve; full specification ranges, material grades and datasheets are issued for tender, submittal and procurement use.
What corrosion protection is available for seawater duty?
Fusion-bonded epoxy to ANSI/AWWA C550, polyurethane and rubber lining, combined with a dry-shaft design that keeps the bearing and stem out of the conveyed fluid. Material selection — ductile iron, 316L or duplex — follows the specified chloride content and velocity. OEM, private-label and bespoke manufacture is supported for contractors, distributors and EPC packages.
What documentation is provided and delivery terms?
Pressure test certificate to EN 12266 or API 598, EN 10204 3.1 material certificates, coating DFT and holiday test reports, WRAS approval where applicable, plus a third-party inspection release when the owner appoints SGS, Bureau Veritas, Intertek or TÜV. Export packing, third-party inspection and consolidated shipment to Gulf ports/global ports are arranged with the order.



